Lakehurstpt
lakehurstpt_update125011.gif
lakehurstpt_update125010.jpg
lakehurstpt_update125009.gif
Welcome to the Specialist Supplier & Manufacturer to the Power Transmission Drives Industry
lakehurstpt_update125008.gif
Home -
About Us -
Services -
Contact -
News -
lakehurstpt_update125007.gif
Copyright remains the property of Lakehurst Limited
Back to Timing Belt Drive Products Index Page -
Timing Pulleys: HTD Pitch Size 14M Taper Bored
lakehurstpt_update125006.jpg
lakehurstpt_update125005.jpg
lakehurstpt_update125004.jpg
Pulleys
No.Teeth
For Belt
W40(40mm)
For Belt
W55(55mm)
For Belt
W85(85mm)
For Belt
W115(115mm)
For Belt
W170(170mm) 
28T  14M-40  14M-55   14M-85   14M-115     
29T   14M-40   14M-55   14M-85    14M-115  
30T  14M-40  14M-55   14M-85    14M-115    
32T   14M-40   14M-55   14M-85    14M-115 
 
34T   14M-40   14M-55   14M-85    14M-115    
36T   14M-40   14M-55   14M-85    14M-115    
38T   14M-40   14M-55   14M-85    14M-115    14M-170
40T   14M-40   14M-55   14M-85    14M-115    14M-170
44T   14M-40   14M-55   14M-85    14M-115   14M-170
48T   14M-40   14M-55   14M-85    14M-115    14M-170
56T   14M-40   14M-55   14M-85    14M-115   14M-170
64T   14M-40   14M-55   14M-85    14M-115   14M-170
72T   14M-40   14M-55   14M-85    14M-115    14M-170
80T   14M-40   14M-55   14M-85    14M-115    14M-170
90T   14M-40   14M-55   14M-85    14M-115    14M-170
112T   14M-40   14M-55   14M-85    14M-115    14M-170
144T   14M-40   14M-55   14M-85    14M-115   14M-170
168T   14M-40   14M-55   14M-85    14M-115    14M-170
192T   14M-40   14M-55   14M-85    14M-115   14M-170
216T   14M-40   14M-55   14M-85    14M-115   14M-170
264T   14M-40   14M-55   14M-85      
Pulleys:Taper Bored
(For Taper bush)
Material Pulleys: Steel C45 E UNI EN 10083-1 with Flanges up to 56 tooth Cast Iron EN GJL-200 UNI EN 1561 with Flanges 64 tooth only, without Flanges from 72 Tooth & above
Taper bored means that the pulley's bore has been pre-machined to suit a size of Taper Bush, the corresponding bush is pre-machined (Bored & Keywayed) to suit either a Imperial or Metric shaft size, this allows mutli shaft fitting from the same pulley type!
lakehurstpt_update125003.jpg
lakehurstpt_update125002.jpg
Information Bar :-
This New feature is there to provide useful links to other pages, further information and Tips you may find of interest?
lakehurstpt_update125001.jpg
Drive Design Service:
-> A Free Drive Selection Service is available upon request, please click on this link to go to our Drive Selection Service Page for details!
Plating Services:
A Full range of add on Plating Finishes is available:
Zinc (Clear & Yellow) Nickel
Chemically Black Phosiphate as well as Hard Andosing for Aluminium Products!
Manufacturing:
-> The company also provides a Manufacturing Service that caters for:-
1- Any requirement outside it's stock ranges!
2- Customers own drawing requirement.
3- Or when a stock pulley is not suitable?
See our manufacturing Capacity
Tips:
Note: Only one pulley' within a timing pulley drive needs to have Flanges to stop belt run off?
Link to Related Products:
-> Taper Bushes
-> HTD 14M Pulleys Pilot Bore
-> HTD 14m Belts - Single/Double Sided - Sleeves & Belting
Listed here is our current standard stock range of Taper Bored Pulleys to suit HTD 14M pitch Timing Belts.
The standard stock range of pulleys are available in twenty one tooth sizes to suit Five standard belt widths of 40(40mm),55(55mm),85(85mm), 115(115mm) and 170(170mm)
Alternatively if you can not find the tooth size you are looking for, then do plase take a look at our Pilot Bore Pulley and Bar range, by using the links below?
Even if you can not find the Tooth size here or within it's pilot bore and bar ranges, the company does also provide a full manufacturing service to cater for a requirement outside it's Standard Stock Ranges?
-> HTD 14M Clampling Plates
-> Spring Loaded Belt Tensioners
-> Adjustable Motor Rails & Bases for Adusting Belt Drive Centre's
UK -Tel: (44) 0121 555 6777 Fax: (44) 0121 555 6779