Lakehurstpt
lakehurstpt_update123011.gif
lakehurstpt_update123010.jpg
lakehurstpt_update123009.gif
Welcome to the Specialist Supplier & Manufacturer to the Power Transmission Drives Industry
lakehurstpt_update123008.gif
Home -
About Us -
Services -
Contact -
News -
lakehurstpt_update123007.gif
Copyright remains the property of Lakehurst Limited
Back to Timing Belt Drive Products Index Page -
lakehurstpt_update123006.jpg
Pulleys
No, of
Teeth
For Belt
Width
15(15mm)
34T   5M-15
36T    5M-15
38T    5M-15
40T    5M-15
44T    5M-15
48T    5M-15
56T    5M-15
64T    5M-15
72T    5M-15
80T    5M-15 
90T    5M-15
112T    5M-15
136T    5M-15
Material Pulleys: Steel C45 E UNI EN 10083-1 with Flanges up to & including 64 Tooth, without Flanges from 72 Tooth & above
Pulleys: Taper Bored (For Taper bush)
Taper bored means that the pulley's bore has been pre-machined to suit a size of Taper Bush, the corresponding bush is pre-machined (Bored & Keywayed) to suit either a Imperial or Metric shaft size, this allows mutli shaft fitting from the same pulley type!
lakehurstpt_update123005.jpg
lakehurstpt_update123004.jpg
Information Bar :-
This New feature is there to provide useful links to other pages, further information and Tips you may find of interest?
lakehurstpt_update123003.jpg
Drive Design Service:
-> A Free Drive Selection Service is available upon request, please click on this link to go to our Drive Selection Service Page for details!
Plating Services:
A Full range of add on Plating Finishes is available:
Zinc (Clear & Yellow) Nickel
Chemically Black Phosiphate as well as Hard Andosing for Aluminium Products!
Manufacturing:
-> The company also provides a Manufacturing Service that caters for:-
1- Any requirement outside it's stock ranges!
2- Customers own drawing requirement.
3- Or when a stock pulley is not suitable?
See our manufacturing Capacity
Tips:
Note: Only one pulley' within a timing pulley drive needs to have Flanges to stop belt run off?
Link to Related Products:
-> HTD 5M Pulleys Pilot Bore
-> HTD 5M Belts - Single/Double Sided - Sleeves & Belting
-> Taper Bushes
lakehurstpt_update123002.jpg
lakehurstpt_update123001.jpg
Listed here is our current standard stock range of Taper Bored Pulleys to suit HTD 5M pitch Timing Belts.
This standard stock range of pulleys are available in thirteen tooth sizes to the standard belt width of 15(15mm)
Alternatively if you can not find the tooth size you are looking for, then do please take a look at our range of Pilot Bore pulleys and Bars, by using the links below!
The company does also provides a full manufacturing service to suit any customer's individual requirement, see our timing pulley manufacturing page for full details?
Looking for a Tooth Size not listed here!
Why not Modify a pilot bore type to take a Taper Bush?
In addition to the Taper Bored Range listed here, the company also provide a modification service of any of its pilot bore pulley range to take a Taper bush (subject to pulley size and design type?) Hence also check out our Pilot Bore Pulley & Bar ranges for any tooth size not listed here, use the links below to see our ranges!
-> HTD 5M Clampling Plates
-> Spring Loaded Belt Tensioners
-> Adjustable Motor Rails & Bases for Adusting Belt Drive Centre's
UK -Tel: (44) 0121 555 6777 Fax: (44) 0121 555 6779