Lakehurstpt
lakehurstpt_update112011.gif
lakehurstpt_update112010.jpg
lakehurstpt_update112009.gif
Welcome to the Specialist Supplier & Manufacturer to the Power Transmission Drives Industry
lakehurstpt_update112008.gif
Home -
About Us -
Services -
Contact -
News -
lakehurstpt_update112007.gif
Copyright remains the property of Lakehurst Limited
Back to Timing Belt Drive Products Index Page -
Timing Pulleys: Classical Imperial Pitch XH (7/8") Taper Bored
lakehurstpt_update112006.jpg
Pulleys
No. of
Teeth
For Belt
Width
200(2")
For Belt
Width
300(3")
For Belt
Width
400(4")
For Belt
Width
500(5")
18T   XH200  XH300  XH400   
20T   XH200   XH300  XH400  
22T   XH200   XH300  XH400   
24T   XH200   XH300  XH400   
26T   XH200   XH300  XH400   
28T   XH200  XH300   XH400   
30T   XH200   XH300   XH400  XH500
32T   XH200   XH300   XH400   
40T   XH200   XH300   XH400   
48T   XH200   XH300   XH400    
60T   XH200   XH300   XH400    
72T   XH200   XH300   XH400  
84T   XH200   XH300   XH400    
96T   XH200   XH300   XH400  
120T   XH200   XH300   XH400    
Pulleys: Taper Bored (For Taper bush)
lakehurstpt_update112005.jpg
lakehurstpt_update112004.jpg
Material Pulleys: Steel C45E UNI EN 10083-1 with Flanges up to & including 40 tooth
Cast Iron EN-GJL-200 UNI EN 1561 without Flanges from 48 tooth & above
lakehurstpt_update112003.gif
Drive Design Service:
Plating Services:
A Full range of add on Plating Finishes is available:
Zinc (Clear & Yellow) Nickel
Chemically Black Phosiphate as well as Hard Andosing for Aluminium Products!
Manufacturing:
-> The company also provides a Manufacturing Service that caters for:-
1- Any requirement outside it's stock ranges!
2- Customers own drawing requirement.
3- Or when a stock pulley is not suitable?
See our manufacturing Capacity
Tips:
Note: Only one pulley' within a timing pulley drive needs to have Flanges to stop belt run off?
Link to Related Products:
This New feature is there to provide useful links to other pages, further information and Tips you may find of interest?
Information Bar :-
-> XH Pitch Pilot Bore Pulleys
-> XH Pitch Belts - Sleeves & Belting
lakehurstpt_update112002.jpg
Taper bored means that
the pulley's bore has
been pre-machined to
suit a size of Taper Bush,
the corresponding bush
is pre-machined (Bored
& Keywayed) to suit either
a Imperial or Metric shaft size, this allows mutli shaft fitting from the same pulley type!
lakehurstpt_update112001.jpg
-> Taper Bushes
-> A Free Drive Selection Service is available upon request, please click on this link to go to our Drive Selection Service Page for details!
Listed here is our current standard stock range of Taper Bored Pulleys to suit the Classical XH (7/8") pitch of Timing Belts.
This Standard Stock range are available in fifteen tooth sizes to suit four standard belt widths of 200(2"), 300(3"), 400(4") and 500(5") which should cater for the majority of power transmission drive applications!
Looking for a Tooth Size not listed here!
Why not Modify a pilot bore type to take a Taper Bush?
In addition to the Taper Bored Range listed here, the company also provide a modification service of any of its pilot bore pulley range to take a Taper bush (subject to pulley size and design type?) Hence also check out our Pilot Bore Pulley & Bar ranges for any tooth size not listed here, use the links below to see our ranges!
Even if you can not find the Tooth size here or within it's pilot bore and bar ranges, the company does also provide a full manufacturing service to cater for a requirement outside it's Standard Stock Ranges?
-> Spring Loaded Belt Tensioners
-> Adjustable Motor Rails & Bases for Adusting Belt Drive Centre's
UK -Tel: (44) 0121 555 6777 Fax: (44) 0121 555 6779